Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
time to coax Flopsy back into life
#16
photos from this morning - whole job took about an hour including removing the
exhaust! I think, the pulley nut being off twice in the last 10yrs was a help though.

Sadly the exhaust heat shield I bought new last year fell to pieces as soon as the
retaining bolts were taken out, so I'm gonna have to find a new one of those, and
one that is made a bit better.

#2292 over the steps, which make an excellent service area Wink
[Image: IMAG0816.jpg]

Heat shield that broke when the bolts were taken out Sad
[Image: IMAG0818.jpg]

our quarry is now in sight!
[Image: IMAG0819.jpg]

cue 35mm socket, large persuading device and determined bloke Smile
[Image: IMAG0821.jpg]

Engine secured, socket applied, and 10 seconds later.....
[Image: IMAG0822.jpg]

One bent pulley!
[Image: IMAG0823.jpg]

Hopefully we'll catch up with RichH over the weekend, so that he can get the
offending article off to the engineering place to have a new one made - who knows,
we could have the car back together again within a couple of weeks, then, oh joy,
the MOT.... lol
Claire Wright  - Club Treasurer
Jul 1981 DeLorean - Flopsy #2292 
Aug 1989 Cavalier 1.6L - Guinney
Apr 2021 Mokka-e Launch Edition - Evie
#170
Reply
#17
not gonna get a new pulley made, lets just say it was about as expensive as getting
one from the USA, but luckilly we have sourced a used one - we just need to remove
it from the engine it is currently attached to and cross the owners palms with currency Wink

Once the pulley and exhaust are back on the car, I'll get the new back tyres fitted, and
then I'll give the car a tune up and then go and see the MOT man........
Claire Wright  - Club Treasurer
Jul 1981 DeLorean - Flopsy #2292 
Aug 1989 Cavalier 1.6L - Guinney
Apr 2021 Mokka-e Launch Edition - Evie
#170
Reply
#18
HUGE thanks to Chrispy for helping us out this afternoon and supplying us with the
much needed crank pulley for #2292 - and thanks also to RichH for an extra pair
of muscles getting it off the engine it was affixed to.

Whilst its sad to see 'Parnham Palace' being prepared for sale, knowing how much
Chris put into buying, designing and building the place, we did get a tour of the new
'Parnham Cottage', which will be something quite special when its finished in a few
months time.

Phill's just going outside now to fit the new pulley, photos to follow! Big Grin
Claire Wright  - Club Treasurer
Jul 1981 DeLorean - Flopsy #2292 
Aug 1989 Cavalier 1.6L - Guinney
Apr 2021 Mokka-e Launch Edition - Evie
#170
Reply
#19
ok, so here we go Smile

Phill putting new pulley on Flopsy's engine:

[Image: IMAG0853.jpg]

[Image: IMAG0854.jpg]

New pulley in place!

[Image: IMAG0856.jpg]

Happy to say, that the engine is now all back together, everything is connected back
up, and the car runs absolutely fine, and there is no longer a visible 'wobble' on the
pulley.

Next jobs, are to get new rear tyres fitted, give the car a quick tune up, fit new
Bluetooth stereo, and then its off to the MOT station! I'll tax the car from the 1st
June, that way I can use it right up until the end of November Smile
Claire Wright  - Club Treasurer
Jul 1981 DeLorean - Flopsy #2292 
Aug 1989 Cavalier 1.6L - Guinney
Apr 2021 Mokka-e Launch Edition - Evie
#170
Reply
#20
Good stuff Claire. Glad you got the pulley sorted.

Chrispy garage is cool. I had a tour when I picked up a used exhaust for LJH..

I remember his place before that. Turns out I lived a couple of streets over from him when I was at Derby Uni in the early 90's.

Regards

Nick H
DOC 650
Jaguar X-Type
Range Rover Sport SDV6 "Rufus" (Mrs H's motor)
DeLorean DMC 12 Vin#2862

My other hobby...
http://www.lccuk.org.uk/
Reply
#21
well, I've given her the once over, the new tyres are on, I've checked the emissions, its
down the MOT man now tomorrow morning............ :|
Claire Wright  - Club Treasurer
Jul 1981 DeLorean - Flopsy #2292 
Aug 1989 Cavalier 1.6L - Guinney
Apr 2021 Mokka-e Launch Edition - Evie
#170
Reply
#22
Ta daaaaaaaaaaaaaaaaaaaaa !!!!!!!!!!! Big Grin Big Grin Big Grin Big Grin Big Grin

[Image: IMAG0959.jpg]

[Image: IMAG0960.jpg]

Big Grin Big Grin Big Grin Big Grin Big Grin
Claire Wright  - Club Treasurer
Jul 1981 DeLorean - Flopsy #2292 
Aug 1989 Cavalier 1.6L - Guinney
Apr 2021 Mokka-e Launch Edition - Evie
#170
Reply
#23
Always a good feeling when you get the pass slip Smile

What tyres did you go for btw? General Grabbers, or did you drop down to 225's?
VIN# 04708, Grey interior, 5 speed, October 1981
DOC 649
ex DOC 562
Reply
#24
225's in the end, Phill and RichH have been on them for a few years with no probs, plus
they are easier to find.

My Pirellis had been on since 2006, so I'd had 6yrs out of them and they were pretty worn
and wouldnt have passed the MOT.
Claire Wright  - Club Treasurer
Jul 1981 DeLorean - Flopsy #2292 
Aug 1989 Cavalier 1.6L - Guinney
Apr 2021 Mokka-e Launch Edition - Evie
#170
Reply


Forum Jump:


Users browsing this thread: 2 Guest(s)