Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Driveshaft to differential oil seals
#1
Hi , has anybody done these seals in here? This seems like the opportune time to do them and there is some oil wetting there so I think they're weeping ( as am I ).

It looks like there is a roll pin to tap out then a castellated but to undo but I assume that will also lose end load on the diff.

Also does anyone have a part cross-reference for the seals?

Thanks!    

Sent from my moto g(7) power using Tapatalk
Richard Hanlon
Derbyshire
DOC 393

1981 DMC-12 VIN 06126
Reply
#2
Back in November, I bought some of these drive shaft seals. I bought two different types so i could compare.

I bought these cheap as chips ones from Ebay:
https://www.ebay.co.uk/itm/Corteco-12018...2749.l2649

I also bought the latest correct and only offering direct from Renault themselves. The Renault part number for them is: 7703087188.
They cost me £45.82 for 2. In my opinion, the Ebay ones will probably do the job just fine (ribbed and shrowded etc same as the Renault ones), but the Renault ones do appear to be a bit better quality (in my opinion). There's quite a bit of a price difference between them obviously, so it comes down to "you pays you money and you take you chances".
Not something you're expecting to replace very often...

You can pull the old seals out and push the new ones in without disturbing the castle nut for the differenital preload. As you say though, you do need to punch out the long roll pins to get at them behind the shaft coupling. Just remember to seal the splines on the shafts when putting them back on after the seals are swapped over to stop gearbox oil migrating out along the splines and on to the garage floor.

Hope that helps.
Rissy
(Forum Member 288)
(DOC Member 663)

May 1981 vin#1458 "LEX"
Grey, Flapped, Black
Chassis: #1073
Engine: #2839

Main Car(s):
2005 BMW M3 in Velvet Blue
2010 Honda Civic Type R in Sapphire Blue (1 of 115 made)
Reply
#3
That's brilliant info, thanks Rissy [emoji846]

Sent from my moto g(7) power using Tapatalk
Richard Hanlon
Derbyshire
DOC 393

1981 DMC-12 VIN 06126
Reply
#4
Did you fit new roll pins by the way, or did you reuse the old ones?

Sent from my moto g(7) power using Tapatalk
Richard Hanlon
Derbyshire
DOC 393

1981 DMC-12 VIN 06126
Reply
#5
I reused my old ones, but it really depends on the condition of them. I can't remember the length of them i'm afraid. (Same as diameter of coupling flange at that location). I *think* the diameter is 6mm?. But you can measure and buy the same again once you've got them out too. It's not like thy're expensive, and you'll find them on the likes of Ebay etc without any bother.
Rissy
(Forum Member 288)
(DOC Member 663)

May 1981 vin#1458 "LEX"
Grey, Flapped, Black
Chassis: #1073
Engine: #2839

Main Car(s):
2005 BMW M3 in Velvet Blue
2010 Honda Civic Type R in Sapphire Blue (1 of 115 made)
Reply
#6
Cheers matey. I managed to get one side out last night after I posted that, and it looks ok. Seals are allegedly on their way...

Sent from my moto g(7) power using Tapatalk
Richard Hanlon
Derbyshire
DOC 393

1981 DMC-12 VIN 06126
Reply
#7
Which seals you going for?
Rissy
(Forum Member 288)
(DOC Member 663)

May 1981 vin#1458 "LEX"
Grey, Flapped, Black
Chassis: #1073
Engine: #2839

Main Car(s):
2005 BMW M3 in Velvet Blue
2010 Honda Civic Type R in Sapphire Blue (1 of 115 made)
Reply
#8
Once I'd seen how easy they were to swap, I elected for the cheapies - I'll be able to get at them again easily enough if they fail.

Thanks again for the info chap. Much obliged.

Sent from my moto g(7) power using Tapatalk
Richard Hanlon
Derbyshire
DOC 393

1981 DMC-12 VIN 06126
Reply
#9
They eventually arrived this morning.    

Sent from my moto g(7) power using Tapatalk
Richard Hanlon
Derbyshire
DOC 393

1981 DMC-12 VIN 06126
Reply


Forum Jump:


Users browsing this thread: 2 Guest(s)