Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Is the TAB do-able without a car lift?
#1
Nearly time for Easter and I have time to do the TABs. I am wondering whether I should spend mega money for a mechanic to do it, or can I do it myself with a pair of jack stands and me lying on the floor.

Has anyone done their TABs on their driveway (I know NickT have done his, but he is very techanical minded and I am still a learner and don't have a garage with a sunk-in tub!)

How can I torque up the TABs if it needs the car to be on the ground? I can't fit under the car this way Cry

Or.... can I change the TABs and all that, torque it up to a safe level (while still on jack stand), and drive approx 3 miles to a garage to borrow their car lift for 2 minutes to torque them up to 55 Ft/pounds correctly? (I know they won't charge me for that :twisted: )
Kind Regards,
John [DOC No. 8]

[Image: signature.jpg]
Reply
#2
Use a jack under the wheel to un-load the TAB to replace it, then jack the car up under the wheel. This pre-loads the bush and you can torque it just fine.
Martin Gutkowski
DeLorean Cars
http://www.delorean.co.uk
Reply
#3
Outatime Wrote:Nearly time for Easter and I have time to do the TABs. I am wondering whether I should spend mega money for a mechanic to do it, or can I do it myself with a pair of jack stands and me lying on the floor.

Has anyone done their TABs on their driveway (I know NickT have done his, but he is very techanical minded and I am still a learner and don't have a garage with a sunk-in tub!)

How can I torque up the TABs if it needs the car to be on the ground? I can't fit under the car this way Cry

Or.... can I change the TABs and all that, torque it up to a safe level (while still on jack stand), and drive approx 3 miles to a garage to borrow their car lift for 2 minutes to torque them up to 55 Ft/pounds correctly? (I know they won't charge me for that :twisted: )

I am lucky I have the luxury of a big gaage and pit.

You could take the car to have its alignment check and if it requires the rear end aligned then you would have to move/ add / remove a shim or too anyway. This way the garage will do this as part of the geometry alignment !

If you are jacking the wheel then at least measure the distance between the top of the rim to the wheel arch with the car on the ground then get this measurement correct with the car up.

Regards,

Nick.
Reply
#4
I have replaced the TABs on my D using drive up ramps if you can borrow a set from somewhere....
Richard H. DOC 365 VIN 1274
http://www.deloreans.co.uk
In theory, theory and practice are the same. In practice, they are not.
Reply
#5
just did my TABs over the weekend. I used bricks Wink


here's the driver's side TAB:
[Image: IMG_1253.jpg]

pass side a little better off.
-------------------------
- Dave Smith

VIN: #00944 DOC: #535
VIN: #03193
Reply
#6
Yes I'm embarrassed to say thats still one thing I have not checked and done on my car. Who's bolts did you use in the end Barson? Toby tab's?
Chris
Membership Secretary DOC UK
2021's DeLorean event: http://www.deloreans.co.uk/forum/showthr...p?tid=6056
VIN#15768 Ex VIN#4584
Reply
#7
Yep - That's a Toby Tab on the right. Smile
-------------------------
- Dave Smith

VIN: #00944 DOC: #535
VIN: #03193
Reply
#8
Ahh, right thanks. Must get a couple ordered.

Chris
Membership Secretary DOC UK
2021's DeLorean event: http://www.deloreans.co.uk/forum/showthr...p?tid=6056
VIN#15768 Ex VIN#4584
Reply
#9
After consultation with an enginnering friend I went for these.
[Image: delorean-trailing-arm-bolts.jpg]


http://specialtauto.com/delorean-parts/suspension.html
Reply
#10
For some reason the heads on those toby tabs look very familiar, look remarkeably aircraft like!!, knock of Boeing me thinks Shock
Chris
Membership Secretary DOC UK
2021's DeLorean event: http://www.deloreans.co.uk/forum/showthr...p?tid=6056
VIN#15768 Ex VIN#4584
Reply
#11
I think Toby is/was an aircraft engineer or something. the TABs are made out of inconel which is commonly used on aircraft.
-------------------------
- Dave Smith

VIN: #00944 DOC: #535
VIN: #03193
Reply
#12
i need to do mine i think, i have access to a ramp now TT
DOC398
VIN#3484
Tourettes Tutor
I have the X factor
Reply
#13
Barson Wrote:I think Toby is/was an aircraft engineer or something. the TABs are made out of inconel which is commonly used on aircraft.

Here's a pic I took earlier in the wheel bay of a 737. I knew I had seen bolt heads like that before[Image: Image010.jpg]

Chris

needs to get out more....
Membership Secretary DOC UK
2021's DeLorean event: http://www.deloreans.co.uk/forum/showthr...p?tid=6056
VIN#15768 Ex VIN#4584
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)